3 thoughts on “How to make a necklace rope on the neck?”

  1. The necklace rope on the neck is as follows:
    Pre -preparation materials: jade line, pearl
    1, 120 cm long red rope, take the middle point, start with the middle line, respectively to both sides, respectively. Preparation, each compilation of 6 snake knots, symmetrical left and right.

    2, after editing, add 1 beads on each side, and then edit 3 snake knots. In fact, don't loosen.

    3, twist the rope 2 cm long, and then continue to make 3 snake knots through a bead, and then make 3 snake knots. Essence

    4, then 2 threads to wear 1 bead, edit 2 snake knots, then wear a bead, then prepare 3 and then 3 again. Snake knot. Don't forget to edit the two sides together, to be symmetrical,

    5, repeat the previous steps according to your preferences, when you feel that the length is appropriate, the knot is tied. Fix the tightness, burn the head with the lighter, and pinch.

    6. Use a short -term fixation at the midline of its symmetrical midline. Can be prepared according to personal preferences.

    7, you can add a beautiful pendant to your own necklace in the end, such a beautiful red rope necklace is prepared.

  2. Materials: rope, line.
    1, first remove the prepared red rope, and then place it outside the other green rope.
    2, next, we repeat the steps of red rope, then knot the green rope, and then put a small bead on it.
    3, then continue to follow the same editing method, then put the beads you choose and tighten it.
    4. Always follow this operation and weave a beautiful red rope necklace.

  3. 1. First prepare two 50cm of 12 -share cords in the middle of the fixation.
    2, then use two lines to hit a right oblique roll, these two lines are now axis.

    3, adding a 35cm line to the left axis also hit a right diagonal roll. You do n’t need to leave too long on the left side of this line.

    4, take a 60cm light rose red thread to fold the tap head on the middle of the golden line.

    5.

    6, the axis winding is not changed to a left oblique roll, and the axis should be straightened, do not bend.

    7, two light rose red threads are obliquely curled on the golden line in the middle.

    8, the golden thread in the middle is to the left axis to make a left oblique roll.
    9, the axis winding does not change, and then make a right oblique roll. The axis should be straightened, do not bend, and then use the light rose red thread on the left to make oblique curls on the golden line in the middle.

    10. Take a 60cm light rose red thread and fold it on the golden line on the middle of the golden line.

    11, the light rose red thread on the right is obliquely rolled on the golden line in the middle, and the middle gold wire to the right to do one right and left oblique roll.
    12, 4 light rose red threads are obliquely rolled on the golden line in the middle.

    13, the golden line in the middle makes a left oblique roll on the left axis.
    14. Cut the cables on both ends of the gold thread and burn it.
    15, the other end is also done in the same way, and the golden line is used to look at the previous step, so that the bow is done.

    16. Take two 60cm of 60cm to get 12 lines of wine red. Tie the center position with the bow with a auxiliary line with one end of the bow. These two wine red threads can also be replaced with the same color line of bow. The effects are different. You can refer to the two hand ropes of white and sky blue.

    17, fixed as shown in the figure, 4 light rose red placed on the side, the wine red and golden thread are put aside.
    18, edit a piece of eight braids, the length of the eight -strand braid is reduced by 2 cm in length and then divided by 2.

    19, the tail of the eight braids is superimposed to the snake knot twice. Each of it must be tightly tightened, and the excess line head cuts off and burn it.
    20, the other end is also tied with auxiliary lines, and another eight -stranded braid of the same length is compiled. This end is used to make a 4 or 5mm winding with 3 stocks. Finally, take off the auxiliary lines on both sides of the bow and make a 4 or 5mm winding. This winding is to cover the irregular position of the eight -strand braid.

Leave a Comment

Shopping Cart